Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterTrusted Gate Repair for Fort Lauderdale Homeowners
A gate that won’t open, drags against the ground, or groans when the motor engages isn’t a nuisance to schedule around. It’s a daily failure point that gets worse each time you force it. Fort Lauderdale’s salt air, afternoon storms, and irrigation overspray work against gate hardware year-round, and most gates we’re called to repair in Victoria Park, Rio Vista, and Coral Ridge have been struggling for weeks before the homeowner picks up the phone.
Vance Gate Repair Fort Lauderdale has repaired and installed 22,000+ gates since Adrian Vance started this company back in 2014, and every single one left with a written price handed over before tools came out and a photographed record of what was found, what was set, and what was replaced. We answer the phone live 24/7 at (754) 399-1474, dispatch background-checked technicians with name and photo before arrival, and back every repair with our 365-Day Done Right Promise.
Key takeaways:
- Same-day gate repair is available throughout Fort Lauderdale, including evenings and weekends
- Written price delivered before any work begins – no surprise invoice at the end
- Documented photo record on every visit: what was found, what was adjusted, what was replaced
- 365-Day Done Right Promise: if it’s not right, we make it right at no charge
- We service nine major automation brands, including Ghost Controls, DoorKing, and Elite
What Our Gate Repair Service Includes
Gate repair in Fort Lauderdale covers a wide range of failures, and most of them are connected. A gate that sags on its hinges puts strain on the motor. A motor working against resistance burns out limit switches and capacitors. A rusted bottom rail lets the pickets separate. We diagnose the whole assembly, not just the symptom, because a one-part repair on a sick gate usually means a callback in six weeks. Here’s what each repair category covers.
Electric Gate Repair
Electric Gate Repair starts with understanding that electric gates depend on a chain of components: the motor, the control board, the wiring run from the house, and the safety sensors that stop the gate when something crosses its path. When any link in that chain fails, the gate won’t respond to the remote, the keypad, or the intercom. We test the circuit end to end, repair or replace the failed component, and leave you with a wiring diagram and photo log so the next technician never has to guess what was done. Fort Lauderdale’s humidity is rough on control boards mounted without proper weather sealing, and we see corrosion-related board failures regularly in older installations.
Automatic Gate Repair
Automatic Gate Repair addresses predictable failures: the opener motor burns out from overloading, the limit switches drift so the gate over-travels or under-travels, or the gearbox strips when the gate meets resistance too many times. We reset limits to the correct travel position, replace stripped gears, and verify the motor’s current draw to confirm it isn’t about to fail. When we replace a motor on an automatic gate in Fort Lauderdale, we photograph the new limit-switch position and record the part number in your job file before we leave.
Hinge & Post Repair
A heavy gate swings on its hinges thousands of times a year, and Fort Lauderdale’s combination of rain, heat, and salt exposure accelerates wear on the hinge pins and the post itself. We provide Hinge & Post Repair to fix worn hinges, reinforce posts that have shifted in the footing, and true the gate so it closes squarely against the stops. A gate that sags half an inch at the latch is already forcing the motor to work harder, and if it isn’t corrected, the motor is the next thing to fail. We weld or bolt new hinge assemblies in place and photograph the finished alignment.
Gate Realignment
Gate Realignment is the repair most Fort Lauderdale homeowners don’t know they need until the latch stops catching or the gate drags a groove into the driveway. The frame has racked slightly over time, the post has settled, or the wheels have worn unevenly, and the gate no longer travels the intended path. We re-level the frame, adjust the wheels or roller tracks, reset the gates stops, and verify that the gate opens and closes with consistent clearance along its entire travel. After realignment, the motor runs quieter and draws less current.
Lock Repair
Gate locks range from simple mechanical deadbolts to solenoid-driven electronic locks tied into the access control system. When a lock fails, the gate either won’t stay closed or won’t let you in without the key, and both failures are security problems, not just convenience problems. We repair or replace the lock mechanism, align the strike plate so the bolt seats cleanly, and integrate the lock with the existing opener system so it releases before the motor starts its cycle. If the lock is electric, we test the wiring and the control signal and document the fix.
Weld & Rust Repair
Aluminum and steel gates in Fort Lauderdale take a beating from the marine air. Steel rusts through the bottom rail and around the hinge mounts. Aluminum corrodes at welded joints and cracks at stress points. We cut out the damaged section, weld in new material, grind it flush, and prime and paint to match, then photograph the repair before and after. If the rust is structural, meaning the gate feels spongy or the pickets are separating from the rail, the repair needs to happen before the gate folds, not after.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Gate Repair
Most gate companies in Fort Lauderdale push you toward the brand they sell. We’d rather fix what’s already on your property. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule because these are the motors actually installed across South Florida, and we keep OEM parts stocked for the most common failures in each line.
Ghost Controls openers show up most often on residential swing gates in older Fort Lauderdale neighborhoods, and the most common failure we see is the control board losing its limit settings after a power surge. DoorKing and Elite models are more common on condominium and community gates, where access control integration matters as much as the motor itself. Mighty Mule units are everywhere on smaller driveway gates, and they fail most often at the photo-eye alignment and the battery backup. Whether your gate runs on any of these brands or something else entirely, we’ll diagnose it with the same written price and photo record on every visit.
BeforeAfterSigns You Need Gate Repair Right Now
Some gate failures are obvious – the gate won’t open, or it’s grinding. Others move slowly, and by the time you notice, the motor has been dying for months. These are the warning signs we see most often in Fort Lauderdale service calls.
- Gate reverses before fully closing. The photo-eye, the infrared beam that stops the gate when something crosses the path, is likely misaligned or dirty, or the closing force sensor is reading resistance that isn’t there. Either way, the gate is searching for a home position and failing to find it. We realign the beam, clean the lenses, and reset the force limits so the gate closes cleanly.
- Motor hums but the gate doesn’t move. The capacitor that gives the motor its starting torque is going, or the gearbox has stripped a gear. The motor draws full current and produces no motion, which cooks the windings and turns a simple capacitor replacement into a full motor swap if it isn’t caught fast. We test the capacitor and the gear assembly before quoting, so you know the exact repair before we touch the gate.
- Gate sits crooked against the driveway. A sagging hinge or settled post is slowly pulling the frame out of square, and every cycle grinds the poor alignment deeper. The latch doesn’t catch, the gate bounces on the wheels, and the motor runs longer than it should. Realignment and hinge work now is a few hundred dollars. A replacement gate slab later is several thousand.
- Visible rust bubbling through the paint. Surface rust on a gate in Fort Lauderdale is not cosmetic. The salt air works through the metal fast, and what looks like a paint blister is often a rust-through in progress. Once the bottom rail swells and splits, water gets inside and rots the gate from within. We cut out the rust, weld in fresh steel or aluminum, and repaint before the corrosion spreads further.
- Remote works intermittently only. The receiver board or the remote’s battery may genuinely be weak, but intermittent signal is more often a worn wiring connection vibrating loose at the control board or a receiver antenna that has corroded. We test the signal strength at the board, inspect every connection, and eliminate the intermittent behavior rather than telling you to try a new battery.
Our Gate Repair Process - Step by Step
Every Vance Gate Repair job in Fort Lauderdale follows the same five steps, and every step produces documentation. You never have to take our word for what was done. You can see it.
- 1
Written estimate before anything else. Our technician arrives, walks the gate with you, tests the motor and the safety sensors, and hands you a written price covering the repair. Under Haven Standard Clause 1, the price on that page is the price you pay – no additional line items, no surprise invoice. If you don’t like the number, you owe nothing and the visit is still documented.
- 2
Diagnosis with photos. Before we disassemble anything, we photograph the gate assembly, the motor, the wiring at the control board, and any visible damage. We read the limit-switch settings with a multimeter and check the capacitor’s rating against the motor nameplate. These readings go into your job record and into your hands before the repair begins.
- 3
Repair with the part numbers you’ll see. We replace the failed component – whether that’s a hinge assembly, a capacitor, a receiver board, or a welded section – and write down the part number of everything installed. If the repair is a weld, we photograph the weld before and after grinding. If it’s a limit-switch reset, we photograph the new position.
- 4
Function test with measured results. The gate runs through at least five full open-and-close cycles while we watch the current draw on the motor and verify the safety beam reverses the gate immediately. We check that the gate opens and closes with consistent clearance and that the latch seats without resistance. The before-and-after measurements go into the photo log.
- 5
Documented handoff. Before the technician leaves, you receive a written record of what was found, what was set, and what was installed, along with photos of each step. The same record is filed with Vance Gate Repair Fort Lauderdale under your address, so any future service visit starts with a complete history, not a fresh guess. Under the 365-Day Done Right Promise, if any part of the repair fails within one year, we make it right with no argument and no additional charge.
How Much Does Gate Repair Cost in Fort Lauderdale?
Gate repair pricing in Fort Lauderdale depends on what failed and how far it has to travel. The most common repair we quote – a photo-eye realignment or limit-switch reset – runs between $95 and $175. Hinge replacement on a standard single swing gate runs $180 to $350 depending on whether the post itself needs reinforcement. Motor capacitor replacement runs $120 to $200. A full motor swap on a swing gate runs $650 to $1,400 depending on brand and whether the arm bracket is intact. Weld and rust repair is priced by the section, with small patches starting around $150 and structural repair of a bottom rail running $250 to $500.
The honest variables are the age of the gate, the brand of the opener, whether the original installer left any documentation, and how long the gate has been failing. A gate that’s been forced to operate against a sagging hinge for six months will often need both the hinge and a new capacitor, because the motor has been stressed the whole time. That’s a $350 to $550 job, not a $200 job.
How do you avoid overpaying? Get the price in writing before you approve anything, and ask what parts are being replaced. A technician who can’t tell you the part number before he installs it hasn’t actually diagnosed your gate. Our free estimates include the written price, the diagnostic photos, and the technician’s recommendations. You keep that documentation whether you hire us or not. If you have a written estimate from another company, bring it to us – we’ll review it at no cost and tell you honestly whether the price and scope are fair. Somebody else’s estimate, our second opinion, no obligation.
Gate Repair Near Fort Lauderdale - Our Service Area
Our technicians dispatch from Fort Lauderdale and cover the surrounding cities daily, including Gate Repair in Wilton Manors, Gate Repair in Oakland Park, Lauderdale Lakes, Lauderhill, Dania Beach, Pompano Beach, Plantation, Sunrise, Hollywood, Tamarac, and Margate. Most Fort Lauderdale addresses are reached in under an hour, and neighboring cities run under 90 minutes from dispatch. If your gate is down and the driveway is blocked, we’ll tell you the technician’s ETA when you call.
You can start with our home page for a full look at everything Vance Gate Repair does, and then call us directly for the written price. This page covers Gate Repair in Fort Lauderdale in detail. If you’re considering something larger, our team handles gate installation, gate motor and opener service, access control, and gate parts and welding as well.
Serving Fort Lauderdale, FL - Our Local Coverage Area
We’re based in the Fort Lauderdale area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Gate Repair in Fort Lauderdale
Gate repair is the diagnosis and correction of mechanical, electrical, or structural failures in a driveway or pedestrian gate system. That includes the motor and control board, the hinges and posts, the wheels and track, the lock, and the metal frame itself. In our shop, gate repair always ends with a written record of what was found, what was fixed, and what parts were installed, so the repair is documented rather than remembered. Call (754) 399-1474 and we’ll schedule the diagnostic visit.
Most common gate repairs in Fort Lauderdale are completed on the first visit, typically within two to three hours. Simple fixes like photo-eye realignment and limit-switch resets are usually done in under an hour, while motor replacements and structural weld repairs can run three to four hours. If a specialized part needs to be ordered, we’ll tell you before we leave, give you the written price for the full repair, and schedule the return visit on the spot.
Most gate repairs in Fort Lauderdale run between $95 for a simple sensor alignment and $1,400 for a full motor replacement, with the most common jobs landing in the $180 to $350 range. The price depends on what failed, the brand of your opener, and whether related components were damaged by the failure. You receive a written price before any work begins, so you’ll never have a surprise invoice at the end. Call (754) 399-1474 and have the technician give you the exact number before you approve anything.
Yes, we service all four of those brands, plus LiftMaster, FAAC, BFT, and Linear, and we stock OEM parts for the most common failures in each line. We don’t steer you toward replacing the motor just because it isn’t a brand we happen to sell. If your Ghost Controls board is fried, we’ll quote you the Ghost Controls replacement board, not a whole new opener. The same applies to every brand we service.
We keep same-day appointment slots available every day of the week, including weekends, and we’ll tell you the technician’s ETA when you call. If your gate is stuck open and the property is unsecured, or stuck closed and you can’t get a vehicle out, we treat that as priority. A live person answers at (754) 399-1474 around the clock – no voicemail tree, no callback queue.
Every gate repair we complete in Fort Lauderdale is covered by our 365-Day Done Right Promise. If the repair fails within one year, we make it right – no argument, no fee, no expiration date within that window. The promise applies to parts and labor, and it’s in writing on your job record. That’s in addition to any manufacturer warranty on the parts themselves.
Clear the area around the gate so the technician can work without moving your vehicles or landscaping, and if possible, have your remote controls and any access codes ready to test. If the gate still operates at all, leave it in the position it naturally rests in – don’t force it open or closed before we arrive, because the symptoms you’re seeing are diagnostic evidence. Beyond that, you don’t need to do anything. We bring the tools, the parts, and the documentation.
Schedule Your Gate Repair Service in Fort Lauderdale Today
When the gate fails, the property is either unsecured or unusable. When both happen at once, you need a technician who can show you the problem, hand you a written price, and leave you with a documented record of what was done. That’s how we’ve worked since 2014, and it’s how every one of our 22,000+ gate repairs has been completed. Call (754) 399-1474 now for a free written estimate. A live person answers 24/7, and your written price is in your hands before the tools come out.
Written by Adrian Vance, Owner at Vance Gate Repair Fort Lauderdale, serving Fort Lauderdale and the surrounding cities since 2014.