Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterTrusted Gate Parts & Welding for Fort Lauderdale Homeowners
When a gate hinge snaps or a post shifts out of square, most Fort Lauderdale homeowners face the same question: fix the part or replace the whole gate? Our answer, after thousands of repairs since 2014, is almost always simpler than you’d expect. We weld, replace, and reinforce the specific components that failed, and we hand you a written price before any work begins. If you’re wondering how much Gate Parts & Welding costs, you’ll get that upfront.
Adrian Vance built this company on commercial access-control documentation. You get the same habit on a residential driveway gate: photos of what was found, part numbers, and a record of what changed. A live person answers the phone at (754) 399-1474 around the clock, and we dispatch technicians to Gate Parts & Welding - Fort Lauderdale neighborhoods from Rio Vista to Victoria Park, usually within hours for urgent hinge or post failures.
This page covers the parts and welding work we do most often: hinges, posts, rails, custom fabrication, rollers, and latches. If you already know what your gate needs, the pricing section below will tell you what Plantation Gate Parts & Welding and Fort Lauderdale services typically cost.
What Our Gate Parts & Welding Service Includes
Every gate is a collection of wear points. The motor gets attention, but it’s often the hinge that failed first. Here’s what we repair, replace, and fabricate on driveways across Fort Lauderdale.
Hinge Replacement
Hinges carry the entire weight of the gate leaf, and South Florida’s salt air accelerates corrosion on exposed metal. You need replacement hinges when the gate sags visibly, drags on the driveway, or makes a grinding noise at the pivot point. We remove the old hinge, inspect the mounting surface for rust damage, and weld or bolt a new one rated for the gate’s exact weight. Every replacement includes photos of the old hinge, the mounting surface, and the new hardware installed.
Post Replacement
A leaning post is the most common cause of a gate that won’t latch or swings past its stop. In Pompano Beach Gate Parts & Welding and Fort Lauderdale, posts shift when the concrete footer cracks, the soil settles after heavy rain, or the post base rusts through at grade level. We cut the old post, set a new one in fresh concrete, and brace it square before welding the hinge or bracket back on. You get a photo log of the footer excavation and the post set, so you know what’s under the surface.
Rail Repair
Gate rails, the horizontal members that hold the pickets or slats, crack where the welded joints meet. You might notice a rattle, a visible split, or the whole gate flexing when it opens. We grind out the crack, weld the joint, and add a reinforcing plate where the original design was underbuilt. If the rail is too far gone, we fabricate a replacement section and weld it in place. Either way, the repair is photographed and documented before we leave.
Custom Welding
Some repairs don’t have a stock part. An ornamental gate with a broken scroll, a driveway gate that needs a new support strut, or a latch post that has to be rebuilt from scratch. Our welders fabricate brackets, reinforcements, and custom sections on-site or in our shop, matched to your gate’s metal and finish. We’ll show you the broken piece next to the new fabrication before it’s installed, so you can see exactly what your money bought.
Gate Rollers
Sliding gates run on rollers, and rollers wear out. The symptom is a gate that shudders, sticks, or makes a metallic scraping sound as it travels. A worn roller also puts extra load on the motor, which shortens its life. We replace the roller, inspect the track for flat spots or debris, and lubricate the axle with the correct product for outdoor Florida conditions. The track gets photographed and measured, not just eyeballed.
Latch & Lock
A latch that slams instead of catches, or a lock that needs a shoulder against the gate to open, is a hinge or post problem in disguise. But sometimes the latch itself is worn, the strike plate has moved, or the lock body is corroded. We adjust, replace, or fabricate latch hardware, and we test the release under load, meaning with the gate actually moving. A latch that works on the bench and fails on the gate is a waste of your time and ours.
Every one of these services falls under the Haven Standard. That means the price is written and handed to you before we start, the work is documented with photos, and the 365-Day Done Right Promise covers everything we touch.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Gate Parts & Welding
Years of commercial access-control work taught Vance Gate Repair one thing that carries over to residential gates: the brand on the motor matters less than the condition of the metal around it. But when a specific part is needed, we know where to go.
We keep OEM hinge pins, bracket hardware, and latch assemblies for Ghost Controls and Mighty Mule swinging-gate openers, the two brands we see most often on Fort Lauderdale residential driveways. For DoorKing and Elite slide gates, we stock replacement rollers and limit-switch components, and we fabricate the mounting brackets that tend to corrode at the post. If your gate carries any of these brands or something else entirely, the parts and welding work is the same discipline: identify the failed component, price it in writing, replace or repair it, and document the job. We don’t steer you toward a new opener when a bracket and a weld return the gate to service.
BeforeAfterSigns You Need Gate Parts & Welding Right Now
These are the failures we see on Fort Lauderdale gates before the homeowner realizes the scope of the problem. If any of these match what you’re seeing, the cost is almost always lower when we address it now rather than after the next storm.
- The gate sags visibly when it’s open. A sagging gate at the free end means the hinge side is failing, the post is leaning, or both. The longer it sags, the more the frame twists, and twisted frames crack at the welds.
- The gate drags across the driveway or concrete. Dragging is a hinge problem until it becomes a motor problem. A gate that fights its own weight strains the opener and eventually strips the limit gears or burns the motor windings.
- You hear a clicking, grinding, or popping sound when the gate moves. Clicking is usually a hinge pin. Grinding is a roller or track. Popping is a weld failing under stress. All three are repairable, but not if they’re ignored.
- The latch doesn’t hold, or the gate bounces back when you close it. The latch is doing its job, telling you the alignment is off. The post has shifted, the hinge has worn, or the gate frame has twisted. Fix the alignment, the latch works again.
- Visible cracks or rust scale on the post, hinge, or rail. In Fort Lauderdale’s humidity, rust is inevitable but manageable. A crack through a post base or hinge plate is beyond surface rust, it’s structural. Welding before the crack propagates is a small job. After it fails, it’s a bigger one.
If you’re seeing any of these, call (754) 399-1474 and describe what you’re looking at. We’ll tell you if it’s a same-week job or a same-day one, and we’ll give you a written price before we touch the gate.
Our Gate Parts & Welding Process - Step by Step
Here’s exactly what happens when you call Vance Gate Repair for parts or welding work in Fort Lauderdale.
- 1
You call and describe the symptom. A live person answers, 24/7. You tell us what you’re seeing: sag, drag, noise, a visible crack. We ask about the gate type, the motor brand if there is one, and when the problem started. From that conversation we can usually tell you whether this is a diagnostic visit or a job we can quote on the spot.
- 2
We inspect and write the price. The technician arrives, inspects the gate, and takes measurements. Hinge pins get checked for play. The post is checked for plumb. The welds are inspected for cracks. After the inspection, you get a written price with the specific parts and work described. That price does not change after the work starts, per Haven Standard Clause 1.
- 3
The work is done with the right tools and materials. We use the correct welding process for the metal on your gate, whether that’s MIG for most galvanized steel or TIG where a cleaner bead is needed on ornamental work. Replacement parts are matched to the gate’s weight rating, not whatever is in the truck. The work area is cleaned when we’re done.
- 4
We test under real conditions. The gate runs through full open and close cycles with the motor connected. The latch engages under load. The hinges move without binding. The post holds square. If anything doesn’t perform, we correct it before we pack up.
- 5
You receive the documentation. Before we leave, you get a photo log of what was found, what was replaced, and what was adjusted. Part numbers are written down. Welded joints are photographed. Under Haven Standard Clause 4, this record is yours and ours, filed against the job so no future technician has to guess what’s under the paint.
How Much Does Gate Parts & Welding Cost in Fort Lauderdale?
A hinge replacement in Fort Lauderdale typically runs $180 to $400 per hinge, depending on the gate’s weight, the metal thickness, and whether we’re welding a new hinge plate or bolting to an intact surface. Post replacement runs $450 to $900 when the old post is cut out, a new one set in concrete, and the gate re-hung square. Rail repairs and custom welding fall in the $250 to $700 range depending on the extent of the fabrication and the length of the weld required. Gate roller replacement is usually $150 to $350, including the track inspection and axle lubrication. Latch and lock work runs $120 to $300 for adjustment and replacement parts.
What moves the price is the condition of the metal around the part. A hinge replacement on a post with good steel is quick. A hinge replacement on a post that’s rusted through at the base becomes a post job. That’s why the written price comes after inspection, not from a phone call. But the price is always written before the work starts, and it doesn’t change.
To avoid overpaying, get a written scope, not a verbal estimate. A verbal quote that says “around four hundred” isn’t a quote; it’s a starting position. Ask what specific parts are being replaced and what happens if the technician finds additional problems when the gate is opened up. Our answer to that second question: the written price already includes the inspection, and any additional work is documented and priced before we proceed.
Every estimate includes the inspection, the written scope, and the photo documentation. If you have a written estimate from another gate company, bring it to us and we’ll review it at no cost. The review is free, and if we can’t beat the price, we’ll tell you that straight.
Gate Parts & Welding Near Fort Lauderdale - Our Service Area
We run parts and welding jobs across Broward County from our Fort Lauderdale base. Gate Parts & Welding in Wilton Manors usually means a technician on-site within the hour. Gate Parts & Welding in Oakland Park runs on the same schedule. We also serve Pompano Beach, Plantation, Sunrise, Hollywood, Dania Beach, Lauderdale Lakes, Lauderhill, Tamarac, and Margate. If you’re anywhere in the Fort Lauderdale metro, call and we’ll give you a straight answer on timing.
Many of our customers come to us from our home page after reading about the documentation habit. Some find us because their neighbor watched a welding repair across the street and asked who did the work. Both paths end at the same place: a written price and a photo record.
Serving Fort Lauderdale, FL - Our Local Coverage Area
We’re based in the Fort Lauderdale area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Gate Parts & Welding in Fort Lauderdale
Gate parts and welding covers the structural and mechanical components of a gate that don’t involve the motor: hinges, posts, rails, rollers, latches, and custom metal fabrication. When these parts wear out, crack, or corrode, a welder replaces or repairs them so the gate moves and closes correctly. It’s the metal framework work that keeps the gate aligned and secure, separate from the electronic opener work.
Most hinge replacements, roller swaps, and latch adjustments are completed in 60 to 90 minutes on-site. Post replacement takes longer because the new concrete footer needs time to set before the gate is re-hung, usually a half-day job with the gate braced in the interim. Custom welding can range from an hour for a simple reinforcement to a full day for complex fabrication. We’ll give you a time range on the written estimate before any work starts.
Gate welding in Fort Lauderdale typically runs $250 to $700 for most rail repairs and reinforcement work, with smaller bracket or hinge-plate welds starting around $180. The price depends on the length of the weld, the thickness of the metal, and whether the area needs surface prep before welding. Every job is quoted in writing after inspection, and that written price doesn’t change. Call (754) 399-1474 to schedule an inspection, estimates are free.
We service all nine major gate automation brands we work with regularly: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. For parts like hinge brackets, roller assemblies, and latch hardware, we stock OEM components for the brands we see most often on Fort Lauderdale driveways, including Ghost Controls, DoorKing, Elite, and Mighty Mule. If your gate carries a different brand, we source the part and quote it in writing before ordering.
Yes, for structural failures like a snapped hinge or a leaning post, we prioritize same-day dispatch across Fort Lauderdale and the surrounding areas. A live person answers the phone 24 hours a day, so you describe the problem and we tell you when a technician will arrive. If the gate is stuck open or won’t secure, that moves to the front of the schedule, and the written price still comes before the work starts.
Every parts and welding repair is covered by the 365-Day Done Right Promise. If the repair is not right, we make it right, no argument and no additional fee, for one full year from the date of service. The promise covers the workmanship and the parts we installed. If a hinge we replaced fails within the year, we replace it again at no charge.
Clear the area around the gate so the technician can access both sides of the post and the full swing of the gate. If you have dogs, secure them inside. Note the brand of your gate opener and write down any specific noises or symptoms you’ve noticed, it helps us diagnose faster. Other than that, you don’t need to do anything; we bring the tools, the parts, and the documentation.
Schedule Your Gate Parts & Welding Service in Fort Lauderdale Today
A gate that sags, drags, or won’t latch is an open invitation, literally. Call (754) 399-1474 and describe what you’re seeing. We’ll give you a written price before we start, a photo record when we finish, and a full year to hold us to the work. A live person answers, day or night.
Written by Adrian Vance, Owner at Vance Gate Repair Fort Lauderdale, serving Fort Lauderdale since 2014.