Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Hollywood, FL
Gate access control is the call we make most often in Hollywood, and the reason usually comes down to the same two things: salt air and concrete-block communities built between the 1960s and 1990s. A keypad that worked fine in October fails by March because the circuit board inside has been breathing Intracoastal moisture for six months. If your gate is not opening, not closing, or not recognizing the code, call us at (754) 399-1474 and we will tell you over the phone whether it sounds like a board, a motor, or a hinge before we ever roll a truck.
Why Hollywood Homes Are Different
Hollywood sits directly on the Intracoastal Waterway with the Atlantic less than two miles east. The prevailing onshore breeze pushes salt-laden air through every residential grid in the city, from the condos along Hollywood Beach to the HOA communities in Emerald Hills and Hollywood Hills. That salt settles on gate hardware and stays there. Hinges that would last fifteen years in Plantation last seven here. Circuit boards corrode at the solder points. Operators rust from the inside out.
The housing stock compounds the problem. Much of Hollywood is concrete block construction from the 1960s through the 1990s, developed as master-planned communities where shared entry gates are a central maintenance liability. Original iron swing gates in these developments are now decades past their intended service life, and the failure we see most is chronic hinge wear: the gate sags, the motor strains to compensate, and the limit switch burns out trying to push a gate that no longer sits level. In the 55-plus communities along Hollywood Boulevard and out toward University Drive, gates run continuously for six months while owners are up north, then fail in January when everyone returns at once. The deferred maintenance cycle in Hollywood is as consistent as the tide.
Our Main Hollywood Services
Most calls from Hollywood homeowners start with a gate that will not move, then turn into a conversation about one of these three jobs.
Gate Repair in Hollywood
Repair work in Hollywood is rarely one isolated failure. A sagging hinge throws off the limit switch, which burns out the motor, which trips the circuit board. We diagnose the whole chain, not just the part that finally died. On a recent job in Emerald Hills, a LiftMaster slide gate had eaten its worm gear because salt corrosion had seized two of the four rollers, and the motor had been fighting the extra drag for months. The fix was rollers first, then the gear, then a reset and photograph of the new limit position. Gate Repair in Hollywood is where we document what we found, what we set, and what we installed on every single visit.
Gate Installation in Hollywood
A new gate in Hollywood needs to be specified for salt air from the first day: aluminum frame where possible, stainless hardware, sealed control boards, and a base plate anchored to concrete that has not already spalled from twenty years of coastal moisture. We measure the opening, check the column or post condition, and write a spec before we quote a number. No one in Hollywood should install a powder-coated steel gate six blocks off the Intracoastal and expect it to look the same in five years. Gate Installation in Hollywood covers material selection, mounting, and the operator pairing in one written price.
Gate Motor & Opener in Hollywood
Operators fail early in Hollywood because the control board breathes humid, salty air every time the housing cools at night. The typical LifMaster or FAAC opener in a coastal Hollywood HOA lasts five to seven years instead of the ten to fifteen you see inland. When we replace a motor, we also inspect the manual-release function, because hurricane season requires a gate that can be locked open quickly when the storm tracks toward Broward. Gate Motor & Opener in Hollywood covers motor replacement, board swaps, and manual-release verification as one job.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Hollywood
Gate access control in Hollywood means the electronics that decide who gets in: keypads, remotes, phone entry, card readers, and video intercoms, all mounted on gates that spend their lives in salt air. The problem this service solves in Hollywood specifically is the corrosion-driven board failure and the programming drift that happens when part-time residents leave for months and the system runs unattended. A keypad installed in a 1980s Hollywood HOA is usually mounted in full sun and facing the prevailing breeze, so the membrane degrades and the contacts oxidize faster than any manufacturer intends. We service every major brand on the gate, including LiftMaster, FAAC, BFT, and Mighty Mule, so the fix follows whatever is already installed rather than a push toward replacement. Here is how Gate Access Control work breaks down in Hollywood.
Keypad Entry
Signs you need it
The keypad works intermittently, ignores certain digits, or lights up but will not release the gate.
What it costs in Hollywood
Keypad replacement in Hollywood typically runs $165-$490, depending on whether we are swapping the keypad only or the keypad plus its control board.
How we do it
We test the keypad at the contact points, check for corrosion behind the faceplate, replace what is failing, program the new codes, and photograph the finished install.
Remote Control
Signs you need it
Remotes work only at close range, stop opening the gate after a power cycle, or a new remote will not pair with an older receiver.
What it costs in Hollywood
Remote programming or replacement in Hollywood typically runs $85-$350, depending on the receiver type and how many remotes need pairing.
How we do it
We identify the receiver frequency, test signal strength at the gate, replace or reprogram the transmitter, and leave the dip-switch or learn-code settings documented.
What Gate Access Control Costs in Hollywood
| Item | Typical range in Hollywood |
|---|---|
| Keypad replacement | $165-$490 |
| Remote programming or replacement | $85-$350 |
| Access control board replacement | $240-$850 |
How long does gate access control repair take in Hollywood?
Most keypad, remote, and board replacements are completed the same day. If the system is an older phone-entry setup tied to a landline, programming can add an hour. We tell you the timeframe and the flat price before any work starts.
Can you service the access control on a shared HOA gate in Hollywood?
Yes. Shared entry gates make up a large portion of our Hollywood access control work. We coordinate with the HOA board or property manager, provide a written scope and price for approval, and document every setting before and after we make changes.
Gate Parts & Welding in Hollywood
Gate parts and welding in Hollywood means addressing the physical structure the automation sits on: the hinges, posts, rails, rollers, and steel that carry the load. In this city, salt air attacks steel from the first day it is installed, and the original iron swing gates in those 1970s and 1980s HOA communities are far past their service life. The problem this service solves in Hollywood is structural decay: a hinge that has rusted through its pin, a post that has rotted inside its concrete footing, a slide-gate rail that has bowed from twenty years of salt and rain. We replace parts and weld on site, and every job leaves a photo record of what was cut out and what went back in. Here is the Gate Parts & Welding work we do most in Hollywood.
Hinge Replacement
Signs you need it
The gate sags visibly, drags on the ground, or the hinge pin has visible rust bloom and the gate no longer swings level.
What it costs in Hollywood
Hinge replacement in Hollywood typically runs $220-$580, depending on the hinge size and whether the post needs reinforcement.
How we do it
We lift and level the gate, cut out the old hinge, weld in the new one, and photograph the weld before and after dressing.
Post Replacement
Signs you need it
The post is leaning, cracked at the base, or the gate no longer aligns with the latch because the post has shifted in its footing.
What it costs in Hollywood
Post replacement in Hollywood typically runs $350-$1,075, depending on the post size, the footing condition, and whether it is a swing or slide gate.
How we do it
We cut the old post at the concrete, break out the footing if needed, set the new post in fresh concrete, and re-hang the gate to level.
What Gate Parts & Welding Costs in Hollywood
| Item | Typical range in Hollywood |
|---|---|
| Hinge replacement | $220-$580 |
| Post replacement | $350-$1,075 |
| Roller replacement | $140-$390 |
Can you weld a gate without removing it from the property in Hollywood?
Yes. Most hinge and rail repairs are welded in place. For heavier structural work, we may need to remove the gate leaf and lay it flat, but we tell you that before quoting. Either way, the price is written before any welding starts.
Do you replace parts on older Hollywood gates where the manufacturer is long gone?
Yes. Many of the original Hollywood iron gates are custom-built with no manufacturer support. We measure, match, or fabricate the replacement part: a hinge, a roller bracket, or a section of rail. The part number and dimensions go into your job record.
Brands We Service in Hollywood
Our Hollywood trucks carry Mighty Mule, LiftMaster, FAAC, and BFT parts as standard stock, plus universal receivers and control boards for older systems. We service every major automation brand on the gate rather than steering you toward a replacement. For the full list, see our brands. Most common parts are on the truck the same day.
Pricing for Gate Repair in Hollywood, FL
| Service | Typical range in Hollywood |
|---|---|
| Keypad replacement | $165-$490 |
| Remote programming or replacement | $85-$350 |
| Access control board replacement | $240-$850 |
| Hinge replacement | $220-$580 |
| Post replacement | $350-$1,075 |
| Roller replacement | $140-$390 |
Two things push a Hollywood gate repair price past the middle of these ranges: salt-corrosion damage that has spread from one part into a neighboring one, and deferred maintenance on shared gates that has been out of service for weeks or months. Either way, the price is written and handed to you before any work starts, with no surprise line items when the job is done.
Neighborhoods We Serve in Hollywood
We run gate repair and access control calls throughout Hollywood every week, from the coastal condos east of A1A to the HOA communities west of I-95 and into the planned developments around University Drive. Typical response time across the Hollywood area is same day for repair calls and next day for welding that requires heavier fabrication.
- Emerald Hills
- Hollywood Hills
- Hollywood Lakes
- Downtown Hollywood
- Hollywood Beach
Service Area - Cities Near Hollywood
Our Hollywood crews also cover the surrounding Broward cities. If you are just north of the city line, see our Fort Lauderdale, FL page. West of Hollywood, we serve Plantation, FL and Pompano Beach, FL. A little further north, Margate, FL residents get the same written-price standard. One dispatch line covers the whole area, and a live person answers 24/7.
Serving Hollywood, FL - Our Local Coverage Area
We’re based in the Hollywood area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Hollywood
Most Hollywood repair calls are same day. Welding and fabrication work that requires cutting out old steel and setting new posts is usually scheduled within one to two days. We tell you the exact arrival window when you call, and a live person answers the phone at any hour.
For private single-family gates, no. For shared entry gates, most Hollywood HOAs require written approval before work begins. We provide a written scope and price you can submit to the board, and we coordinate directly with property managers when needed.
Yes, measurably. Hinges, rollers, and control boards in Hollywood fail in roughly half the time they do in inland Broward cities because the salt-laden onshore breeze off the Intracoastal settles on metal and accelerates oxidation. We spec materials and protect electronics for that specific environment.
Call Vance Gate Repair at (754) 399-1474 for a written, upfront price on any gate repair, access control job, or welding work in Hollywood. Adrian Vance founded the company in 2014 on commercial access-control documentation standards, and every Hollywood job still follows that same discipline: written scope, written price, and a photo record when we leave.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Hollywood Customers Say
"Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."
- Camille R."Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B."The safety loop had never been installed correctly by the previous company. They showed me the reading, fixed it, and did not charge me for the diagnosis."
- Patrick H.