Linear Gate Motor & Opener Nationwide

Linear Gate Motor & Opener in Fort Lauderdale: What to Know First

We repair and install Linear gate motors and openers across Fort Lauderdale, independent of any manufacturer program. Most Linear swing-gate repair calls in the area are done in a single visit, and most Linear motor replacements run between $650 and $1,250 depending on the model line and whether the arm bracket and mounting post survived. You’ll get our price in writing before we touch a tool. This page is for Fort Lauderdale homeowners running a Linear operator on a driveway gate, and if you need us now, call (754) 399-1474.

Call (754) 399-1474

How Linear Products Fail - and How We Fix Them

Linear operators fail in patterns, and after a decade of working on them across Fort Lauderdale, we know which patterns show up on which models. Here’s what we actually find when we open the control box.

• Linear LDO50 and LDO33 swing arms: the limit cams drift. On these smaller residential swing operators, the mechanical limit cams wear at the edges and the gate starts stopping short or over-traveling. The arm works, the motor hums, but the gate no longer closes flush. We reset the limits, check travel against the physical stops, and if the cam surface is worn, we replace the cam assembly rather than the whole arm.
• Linear APeX and MegaCode receivers: interference false-starts in Fort Lauderdale. The single-channel receivers on older Linear openers pick up stray RF from marine radios and condominium security systems in the Fort Lauderdale area, which leaves homeowners convinced their gate is haunted. We shield the receiver, relocate the antenna, and on operators with a MegaCode board we verify the rolling code actually rolled, not just check the LED. A false-start fix is usually a forty-minute job.
• Pro-Strong and Pro-Series slide motors: salt air and corroded limit switches. Linear slide operators last well mechanically, but the external limit switches on the Pro-Strong line are exposed, and Fort Lauderdale’s salt air eats the contacts. The motor runs fine, the gate just doesn’t know where it is. We replace the limit switches with sealed units and photograph the new positions for your record.
• LDO50 arm with a dead capacitor: the gate groans but won’t move. This one gets misdiagnosed as a dead motor all the time. The capacitor is a $25 part; the motor assembly is a $400-plus part. On a Linear LDO50, if the arm makes a loaded thrum but doesn’t travel, we pull the cap and test it before anything else. Fort Lauderdale’s heat and humidity age capacitors faster than the motor itself, and we see this weekly.
• Battery backup on Linear openers: the charger board fails first, not the battery. On Linear operators equipped with battery backup, the charging board is usually the point of failure, while the battery itself still holds a charge after being condemned by another company. We test the pack under load, test the charger output, and replace the failed component rather than the whole setup. That’s the difference between an $80 repair and a $300 one, and you see it on the written quote before we start.

Our Linear Gate Motor & Opener Process

Every Linear job follows the same sequence, whether it’s a repair, a motor replacement, or a full operator install. This is how we work in Fort Lauderdale.

1. 1
   We inspect the gate first, not the operator. A Linear motor fighting a sagging gate will never run clean. We check the hinges, the rack, the rollers, the physical stops, and we measure the gate’s travel weight before touching the opener.
2. 2
   We diagnose the Linear unit at the board level. We test input voltage, capacitor condition, limit-switch continuity, and receiver response. Name what you found, name what it costs, name what you left behind.
3. 3
   We hand you the written price before any work starts. That’s Haven Standard Clause 1. The number on the quote is the number on the invoice. If you decide not to proceed, you owe nothing.
4. 4
   We source Linear OEM parts when they matter, and tell you when they don’t. A Linear-specific control board should be OEM. A generic capacitor, a sealed limit switch, a photo-eye, a transformer: those can be quality aftermarket without shortening the life of the operator. We’ll show you the difference and let you choose.
5. 5
   We install, set, and test the full cycle. We run the gate through open and close at least five times, test the auto-reverse and the photo-eye twice, and verify the manual release is still accessible.
6. 6
   We hand you a photo log and a written record of every part number installed and every limit reading. Before we leave, you have evidence. That’s Clause 4, on every job, at no additional charge.

Before

After

What Linear Gate Motor & Opener Costs in Fort Lauderdale

Here are the numbers we write on estimates in the Fort Lauderdale market every week.

• Linear swing-arm motor replacement: $650 to $1,100, installed, including limit setting and a full-cycle test. The range depends on the model (LDO33 vs LDO50 vs APeX), whether the mounting bracket is intact, and whether the control board needs to come across from the old system.
• Linear opener repair, component-level: $140 to $400. Capacitor replacement, limit-switch replacement, receiver swap, photo-eye alignment, transformer replacement. The higher end covers a board-level repair, not a whole-board swap.
• Linear slide-gate motor replacement: $900 to $1,400 depending on the Pro-Strong or Pro-Series model and the condition of the rack and drive sprocket.
• Full Linear operator installation with battery backup: $1,200 to $1,900 including the operator, backup, safety edges, photo-eyes, and wiring. New power runs and concrete work are quoted separately, in writing, before any cutting starts.

What moves the price is the condition of what’s already on the ground: the hinges, the rack, the bracket, the wiring. We’ll name those on the estimate so you can see exactly what you’re paying for. Estimates are free, and there’s no charge to come out and look. Call (754) 399-1474.

Why Fort Lauderdale Homeowners Call Vance Gate Repair Fort Lauderdale for Linear Work

We service nine gate-automation brands, including LiftMaster, Mighty Mule, Ghost Controls, DoorKing, and Linear, which means when we look at your Linear opener we’re not angling to convert you to a brand we happen to sell more of. We fix what’s on the property, and we tell you honestly when a Linear operator is worth repairing and when it’s past the point. Adrian Vance built this company out of commercial access-control work, and the documentation habit from that world, wiring diagrams, photo logs, written part numbers, came into every residential job. Every repair we complete is covered by our 365-Day Done Right Promise: if it’s not right, we make it right, no fee, no argument, for a full year.

And when you call, a live person answers. 24 hours a day, seven days a week. No voicemail queue, no answering service that promises to pass a message along. Call (754) 399-1474 and you’ll get one of our dispatch team on the line, and a background-checked, uniformed technician’s name and photo before they arrive.

FAQs