Linear Gate Installation Nationwide

Linear Gate Installation in Fort Lauderdale: What to Know First

Linear gate installation in Fort Lauderdale means mounting the motor, arms, brackets, and safety hardware for a Linear operator on a new or existing gate. We’re an independent Linear service provider, not a factory-authorized dealer, and most installations run between $850 and $2,400 depending on the gate type, the Linear model, and whether the site needs new posts or conduit. You’ll get the written price before we pick up a single tool, and most jobs are finished in one day.

Call (754) 399-1474

This page is for homeowners in Fort Lauderdale who already own a Linear opener, are buying one, or have a builder who spec’d Linear and want to know what the installation actually involves, what it costs, and what goes wrong. If you have questions about your specific setup, call (754) 399-1474. A live person answers, and the estimate is free.

How Linear Products Fail - and How We Fix Them

• Linear LDO50 swing-arm operators lose the close limit slowly, usually after two or three salt-season summers. The limit nuts inside the actuator body walk a few degrees at a time as the nylon inserts wear, and the gate starts stopping a half-inch short of closed. Most companies swap the board. We reset the limits, photograph the new positions, and tell you if the wear is accelerating. That’s a $180 repair, not a $900 board replacement.
• The Linear APeX series (APW, APX, and the older LRA linear-ram arm) is picky about the mounting plate being dead level. We see Fort Lauderdale driveway gates where a hairline slope in the concrete pad, two degrees or so, causes the arm to bind at mid-travel and the opener to fault out intermittently. A shim kit and remeasured bracket geometry fixes it. Most installers just crank the force settings up, which shortens the motor life. We won’t do that.
• Linear MCS and M3S slide operators accumulate corrosion on the limit-switch terminals faster in Fort Lauderdale than almost anywhere else in the country. The humidity plus salt air gets into the board enclosure through the knockouts. Symptom: the gate opens fine but won’t close, or closes halfway and reverses. We clean and reseal the terminals, replace the switch if the contacts are pitted, and seal the knockouts with marine-grade grommets. If you’re near the Intracoastal, this is the failure you’ll see first.
• Linear’s photo-eye wiring (the infrared beam that stops the gate if something crosses the path) uses thin 22-gauge wire, and landscapers accidentally cut it more often than anyone wants to admit. The gate will open from the keypad but won’t close at all, because the board reads the cut line as an obstruction. We run new 18-gauge direct-burial wire in conduit where the hedge line meets the gate rail. Same problem, fixed to last.
• Older Linear swing-gate arms like the LRA series develop a “dead spot” in the middle of travel. That’s usually not the motor, it’s the lead-screw bushing wearing into an oval. The arm hesitates for a beat, then surges. Some companies will tell you the arm is shot and sell you a new operator. We replace the bushing and lead-screw assembly when the arm housing is still sound, which it is about eight times out of ten. You buy a $90 part, not a $1,400 opener.

Our Linear Gate Installation Process

1. 1
   Site check and measurements before anything is quoted. We confirm gate weight, hinge post integrity, slab condition, conduit and power availability, and the exact Linear model you have or want. We shoot wiring drawings from the transformer to the operator.
2. 2
   Written price before any work starts. You’ll have a line-item sheet that names the operator, brackets, conduit runs, photo-eye hardware, and labor. No ranges, no allowances, no “to be determined.”
3. 3
   Parts decision made with you, not for you. If your Linear operator is current and repairable, we use OEM Linear parts. If it’s a dead board on an older LRA, we’ll show you the aftermarket option and the tradeoff in plain language. You decide with the price in front of you.
4. 4
   Mounting and wiring to Linear spec. Operators leveled on a real mounting plate, terminals torqued, photo-eyes aligned with a meter, not by eyeball, and every connection documented.
5. 5
   Testing under load, not just dry-cycling. We run the gate through open, close, obstruction, and auto-reverse with the gate actually attached, and we adjust force and limits to Linear’s tolerance, not “close enough.”
6. 6
   Photo log and written record left with you. Every adjustment, every part number, every limit-switch reading. If anyone works on that gate in five years, they’ll see exactly what we set and why.

Every installation carries our 365-Day Done Right Promise: if the installation is not right, we make it right. No argument, no fee, no expiration date within that year.

Before

After

What Linear Gate Installation Costs in Fort Lauderdale

Plan on $850 to $2,400 for a typical residential Linear gate installation. A single swing-gate arm install with existing conduit and a functioning photo-eye usually lands around $950 to $1,400. A double swing-gate, which needs two arms and an additional photo-eye relay, runs $1,600 to $2,200. New direct-burial conduit from the house to the gate adds $180 to $450 depending on the run, and a keypad or intercom with the install adds $150 to $400.

The biggest variables are gate weight and geometry. Linear’s LDO50 handles most Fort Lauderdale swing gates up to 700 pounds, but a solid aluminum security gate from a company like AmeriGate or Elite can weigh more, and the heavier the gate, the more the bracket and post reinforcement matter. We never guess at weight, we measure it. Before any work starts, you’ll have the exact price in writing. Call (754) 399-1474 and we’ll set up a time to come look. The estimate is free.

Why Fort Lauderdale Homeowners Call Vance Gate Repair Fort Lauderdale for Linear Work

We’re not the only company in Fort Lauderdale that will install a Linear opener, but here’s what we do that others usually don’t: we hand you a written price before work starts, and we leave a photographed record of everything we touched. Adrian Vance started this company in 2014 doing commercial access-control work, where a wiring diagram and a written scope were part of the job. We brought that habit into residential work. Name what you found, name what it costs, name what you left behind.

We service nine automation brands, including LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so if your property has a different operator on the pedestrian gate and a Linear on the driveway, one company handles both. Our technicians are background-checked, uniformed, and we send their name and photo before they arrive. And you’ll reach a live person when you call, any hour, any day.

FAQs